尊龙凯时

高速线缆

标准协议光?

兼容协议光?

其它种类光器件

手艺支持

QSFP+转4*10G SFP+分支型无源电缆

0.0/5 rating (0 votes)

Description

F-tone公司提供QSFP+ 转 4*10G SFP+ 分支型无源电缆、40G QSFP+ to 4×10G SFP+ Breakout Passive Copper Cable ,应用于客户侧40G以太网和10G以太网LAN中 ,该产品普遍应用于焦点路由器和数据中心场景中 。100%完善兼容全系列品牌交流机,路由器,PDH/SDH传输装备,EPON,GPON,10G EPON,10G GPON,WDM PON基站等等全系列装备

QSFP-4SFP-Cables

Hybrid Passive Copper QSFP+ to 4x SFP+

40G QSFP+ to 4x 10G SFP+ Direct Attach Passive Copper Cables

Features

  1. Hybrid cable conforms to the Small Form Factor SFF-8436 and SFF-8431
  2. Support for multi-gigabit data rates :1.0 Gbps - 10.3125 Gbps (per channel)
  3. Maximum aggregate data rate: 41.25 Gbps (4 x 10.3125Gbit/s)
  4. Hybrid cable link length up to 5m (passive limiting)
  5. High-Density QSFP 38-PIN and 4x SFP 20-PIN Connector
  6. Power Supply :+3.3V
  7. Low power consumption: 0.02 W (typ.)
  8. Temperature Range: 0~ 70 °C

Applications

40G QSFP+ to 4×10SFP+

  1. 10G/40Gigabit Ethernet
  2. InfiniBand SDR, DDR, QDR
  3. Switches, Routers, and HBAs
  4. Data Centers
  5. Fibre Channel

STANDARDS COMPLIANCE

QSFP+

  1. SFF-8436
  2. QDR InfiniBand
  3. QSFP+ MSA
  4. RoHS Compliant

SFP+

  1. SFF-8431
  2. SFP+ MSA
  3. RoHS Compatible

Product Description

The QSFP+ to 4x SFP+ Passive cable assemblies are high performance ,cost effective for SFP+ and QSFP+ equipment interconnects . The Hybrid cables are compliant with SFF-8436 and SFF-8431 specifications. It is offer a low power consumption ,short reach interconnect applications. The cable each lane is capable of transmitting data at rates up to 10Gb/s ,providing an aggregated rate of 40Gb/s.

Recommended Operating Conditions

Parameter

Symbol

Min

Typical

Max

Unit

Storage Ambient Temperature

 

-40

 

+85

°C

Operating Case Temperature

Tc

0

 

+70

°C

Power Supply Voltage

VCC3

3.14

3.3

3.47

V

Power Dissipation

PD

   

0.02

W

QSFP+ Pin Descriptions


Pin

Logic

Symbol

Name/Description

Notes

1

 

GND

Ground

1

2

CML-I

Tx2n

Transmitter Inverted Data Input

 

3

CML-I

Tx2p

Transmitter Non-Inverted Data Input

 

4

 

GND

Ground

1

5

CML-I

Tx4n

Transmitter Inverted Data Input

 

6

CML-I

Tx4p

Transmitter Non-Inverted Data Input

 

7

 

GND

Ground

1

8

LVTTL-I

ModSelL

Module Select

 

9

LVTTL-I

ResetL

Module Reset

 

10

 

Vcc Rx

+3.3V Power Supply Receiver

2

11

LVCMOSI/O

SCL

2-wire serial interface clock

 

12

LVCMOSI/O

SDA

2-wire serial interface data

 

13

 

GND

Ground

1

14

CML-O

Rx3p

Receiver Non-Inverted Data Output

 

15

CML-O

Rx3n

Receiver Inverted Data Output

 

16

 

GND

Ground

1

17

CML-O

Rx1p

Receiver Non-Inverted Data Output

 

18

CML-O

Rx1n

Receiver Inverted Data Output

 

19

 

GND

Ground

1

20

 

GND

Ground

1

21

CML-O

Rx2n

Receiver Inverted Data Output

 

22

CML-O

Rx2p

Receiver Non-Inverted Data Output

 

23

 

GND

Ground

1

24

CML-O

Rx4n

Receiver Inverted Data Output

 

25

CML-O

Rx4p

Receiver Non-Inverted Data Output

 

26

 

GND

Ground

1

27

LVTTL-O

ModPrsL

Module Present

 

28

LVTTL-O

IntL

Interrupt

 

29

 

Vcc Tx

+3.3V Power supply transmitter

2

30

 

Vcc1

+3.3V Power supply

2

31

LVTTL-I

LPMode

Low Power Mode

 

32

 

GND

Ground

1

33

CML-I

Tx3p

Transmitter Non-Inverted Data Input

 

34

CML-I

Tx3n

Transmitter Inverted Data Input

 

35

 

GND

Ground

1

36

CML-I

Tx1p

Transmitter Non-Inverted Data Input

 

37

CML-I

Tx1n

Transmitter Inverted Data Input

 

38

 

GND

Ground

1

Note 1: GND is the symbol for signal and supply (power) common for the QSFP+ module. All are common within the QSFP+ module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.

Note 2: Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrent- ly. Requirements defined for the host side of the Host Edge Card Connector are listed in Table 6. Recommended host board power supply filtering is shown in Figure 4. Vcc Rx Vcc1 and Vcc Tx may be internally connected with- in the QSFP+ Module module in any combination. The connector pins are each rated for a maximum current of 500 mA.

SFP+ Pin Descriptions

Pin

Logic

Symbol

Name/Description

Notes

1

 
VeeT
Transmitter Ground
 

2

LV-TTL-O

TX_Fault

N/A

1

3

LV-TTL-I

TX_DIS

Transmitter Disable

2

4

LV-TTL-I/O

SDA

Tow Wire Serial Data

 

5

LV-TTL-I

SCL

Tow Wire Serial Clock

 

6

 

MOD_DEF0

Module present, connect to VeeT

 

7

LV-TTL-I

RS0

N/A

1

8

LV-TTL-O

LOS

LOS of Signal

2

9

LV-TTL-I

RS1

N/A

1

10

 

VeeR

Reciever Ground

 

11

 

VeeR

Reciever Ground

 

12

CML-O

RD-

Reciever Data Inverted

 

13

CML-O

RD+

Reciever Data Non-Inverted

 

14

 

VeeR

Reciever Ground

 

15

 

VccR

Reciever Supply 3.3V

 

16

 

VccT

Transmitter Supply 3.3V

 

17

 

VeeT

Transmitter Ground

 

18

CML-I

TD+

Transmitter Data Non-Inverted

 

19

CML_I

TD-

Transmitter Data Inverted

 

20

 

VeeT

Transmitter Ground

 

1. Signals not supported in SFP+ Copper pulled-down   to VeeT with 30K ohms resistor

2. Passive cable assemblies do not support LOS and TX_DIS

Ordering information

Part Number

Product Description

QSFP-4SFPPC-01

QSFP+ To 4X SFP+ Direct Attach Cables, 1m (30AWG),0?C ~ +70?C

QSFP-4SFPPC-03

QSFP+ To 4X SFP+ Direct Attach Cables, 3m (30AWG),0?C ~ +70?C

QSFP-4SFPPC-04

QSFP+ To 4X SFP+ Direct Attach Cables, 5m (28AWG),0?C ~ +70?C

 

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone before they become applicable to any particular order or contract. In accordance with the F-tone policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone or others. Further details are available from any F-tone sales representative.

 

Search

【网站地图】【sitemap】